Includes commonly used abbreviations, full terms, units, and connector models. “—” indicates that the term itself is already a complete word, model designation, or label and does not require expansion.
| English / Abbreviation | Full English Name or Original Term | Meaning and Common Usage |
|---|---|---|
| ACC | Accelerometer | Accelerometer; used for attitude detection and self-leveling functions. |
| Acro | Acrobatic | Acrobatic / angular-rate control mode; the sticks control rotation rate, and the Drone normally does not automatically level when the sticks are released. |
| ADC | Analog-to-Digital Converter | Analog-to-digital converter; used to sample analog signals such as voltage and current. |
| AGL | Above Ground Level | Height above ground level. |
| AHRS | Attitude and Heading Reference System | Attitude and heading reference system. |
| AIO | All-in-One | All-in-one design; the specific integrated modules depend on the product. |
| Air Unit | — | Air unit / onboard video transmission unit. |
| Airframe | — | Drone structure, including the frame and other load-bearing components. |
| Altitude | — | Altitude; may refer to elevation, relative altitude, or height above ground depending on context. |
| Analog | — | Analog; such as analog video transmission or analog cameras. |
| Angle Mode | — | Self-leveling mode; when the roll and pitch sticks are released, the Drone tends to return to level. |
| ANT | Antenna | Antenna; commonly used as a connector or pad label. |
| Antenna | — | Antenna; used for transmitting and receiving wireless signals. |
| ARF | Almost Ready to Fly | Almost-ready-to-fly package; additional equipment or assembly may still be required. |
| Arm | — | Arm; enables the flight controller to drive the motors. It can also refer to an arm of the frame. |
| Attitude | — | Attitude; the roll, pitch, and yaw orientation of the Drone. |
| AUX | Auxiliary | Auxiliary; commonly refers to auxiliary radio channels used to switch functions. |
| AWG | American Wire Gauge | American Wire Gauge; a smaller number generally indicates a thicker wire. |
| Axis | — | Axis; such as the roll, pitch, or yaw axis. |
| Band | — | Frequency band / channel group; the exact meaning depends on the wireless system. |
| Bandwidth | — | Bandwidth; the frequency range occupied by a signal or communication channel. |
| BARO | Barometer | Barometer; commonly used to estimate altitude. |
| BATT / BAT | Battery | Battery; commonly used as a power connector or parameter label. |
| Battery | — | Battery. |
| Battery Strap | — | Battery strap. |
| BEC | Battery Eliminator Circuit | Voltage regulation circuit used to power receivers, flight controllers, servos, and other devices. |
| BF | Betaflight | Common abbreviation for Betaflight flight controller firmware and its ecosystem. |
| Bind / Binding | — | Bind / Binding; establishes a connection between a transmitter and receiver. |
| Bitrate | — | Bitrate; the amount of data transmitted or encoded per unit of time. |
| Blackbox | — | Blackbox; records flight controller operating data for analysis and tuning. |
| BNF | Bind-N-Fly | Bind-and-fly product; required supporting equipment depends on the product package. |
| Bootloader | — | Bootloader; used to start the system and support firmware flashing. |
| Brushless Motor | — | Brushless motor; commonly used as the propulsion motor in FPV drones. |
| Buzzer | — | Buzzer; used for status indications, alarms, or locating a Drone. |
| Calibration | — | Calibration; such as accelerometer, voltage, current, or stick calibration. |
| Camera | — | Camera. |
| CAN | Controller Area Network | Controller Area Network bus; used for communication between flight controllers and peripherals. |
| Canopy | — | Canopy; used to cover, secure, or protect Drone components. |
| CCW | Counterclockwise | Counterclockwise; commonly used to indicate motor and propeller rotation direction. |
| Cell | — | Battery cell / individual cell. |
| CF | Carbon Fiber | Carbon fiber; a common frame material. |
| CH | Channel | Channel; may refer to a radio control channel or video transmission channel. |
| Charger | — | Charger. |
| Cinewhoop | — | A type of FPV drone with propeller protection, typically designed for smooth cinematic filming. |
| CLI | Command-Line Interface | Command-line interface; used to view or modify flight controller settings. |
| CMOS | Complementary Metal-Oxide-Semiconductor | Complementary metal-oxide-semiconductor; in cameras, commonly refers to a CMOS image sensor. |
| Coaxial Cable | — | Coaxial cable; commonly used between cameras and air units or for RF connections. |
| Connector | — | Connector / plug / socket. |
| CP | Circular Polarization | Circular polarization; a type of antenna polarization. |
| CRSF | Crossfire protocol | Crossfire communication protocol; also used between many ELRS receivers and flight controllers. |
| CUR / CURR | Current | Current; commonly used as a current-sensing pad or parameter label. |
| Current | — | Electrical current. |
| CW | Clockwise | Clockwise; commonly used to indicate motor and propeller rotation direction. |
| dB | Decibel | Decibel; a logarithmic unit used to express a ratio. |
| dBi | Decibels relative to an isotropic radiator | Unit of antenna gain relative to an ideal isotropic radiator. |
| dBm | Decibels relative to one milliwatt | Power unit referenced to 1 mW; commonly used for signal strength and RF power. |
| DC | Direct Current | Direct current. |
| Deadband | — | Deadband; small input changes within a defined range are ignored. |
| Desync | Desynchronization | Desynchronization; usually refers to a brushless motor losing synchronization with the ESC drive signal. |
| DFU | Device Firmware Upgrade | Device Firmware Upgrade; commonly refers to the USB firmware flashing mode of a flight controller. |
| Digital | — | Digital; such as digital HD video transmission. |
| Disarm | — | Disarm; exits the state in which the motors can be driven. |
| Diversity | — | Diversity; uses multiple antennas or receive paths to improve reception. |
| Downlink | — | Downlink; usually refers to data transmission from the airborne side to the ground side. |
| Drift | — | Drift; gradual deviation in attitude, position, or measurement results. |
| Drone | — | Unmanned aerial vehicle / Drone. |
| DShot | Digital Shot | Digital ESC control protocol, such as DShot300 and DShot600. |
| Duct | — | Duct / airflow shroud surrounding a propeller; not equivalent to every type of propeller guard. |
| DVR | Digital Video Recorder | Digital video recorder / recording function; commonly found in FPV goggles and receiver units. |
| EIRP | Equivalent Isotropically Radiated Power | Equivalent isotropically radiated power; takes transmitter power, feedline loss, and antenna gain into account. |
| EKF | Extended Kalman Filter | Extended Kalman Filter; used to fuse sensor data and estimate attitude and position. |
| ELRS | ExpressLRS | Open-source radio control link system. |
| EMI | Electromagnetic Interference | Electromagnetic interference. |
| ESC | Electronic Speed Controller | Electronic speed controller; controls motor operation. |
| ESR | Equivalent Series Resistance | Equivalent series resistance; commonly specified for capacitors. |
| EXP / EXPO | Exponential | Exponential curve; adjusts the relationship between stick input and control response. |
| Exposure | — | Exposure; affects image brightness and motion appearance. |
| Failsafe | — | Failsafe; performs a predefined action when signal loss or another abnormal condition occurs. |
| Fan | — | Fan; commonly used to cool air units or receiver units. |
| FC | Flight Controller | Flight controller, abbreviated as FC. |
| FEC | Forward Error Correction | Forward error correction; improves resistance to data errors in communication. |
| FF | Feedforward | Feedforward; generates a response in advance based on changes in control input. |
| FHSS | Frequency-Hopping Spread Spectrum | Frequency-hopping spread spectrum; a wireless communication technology. |
| Filter | — | Filter; processes signals in control systems or incoming light in optical systems. |
| Firmware | — | Firmware; low-level software running on a device. |
| Flight Mode | — | Flight mode; such as self-leveling, acro, altitude hold, or navigation mode. |
| FOV | Field of View | Field of view; describes the visible range of a camera or goggles. |
| FPS | Frames Per Second | Frames per second; video frame rate. |
| FPV | First-Person View | First-person view; real-time viewing through an onboard camera. |
| Frame | — | Frame; the structural frame of a Drone. In video contexts, it can also mean a single image frame. |
| Freestyle | — | Freestyle flying; focuses on maneuvers, flight lines, and creative expression. |
| Frequency | — | Frequency. |
| FW | Firmware / Fixed Wing | May refer to firmware or fixed wing depending on context. |
| Gain | — | Gain; may refer to antenna, image, or control gain. |
| GCS | Ground Control Station | Ground control station; used for mission planning, status monitoring, and other functions. |
| GHz | Gigahertz | Gigahertz; a unit of frequency, such as 2.4 GHz and 5.8 GHz. |
| Gimbal | — | Gimbal; in radio controller contexts, it may also refer to the stick assembly. |
| GND | Ground | Electrical ground / reference ground. |
| GNSS | Global Navigation Satellite System | General term for global navigation satellite systems, including GPS and BeiDou. |
| Goggles | — | FPV goggles / head-mounted display device. |
| GPS | Global Positioning System | Global Positioning System; specifically refers to the U.S. satellite navigation system. |
| Ground Station | — | Ground station; may refer to a ground control system or ground video receiver equipment. |
| GYRO | Gyroscope | Gyroscope; measures the angular velocity of the Drone. |
| HD | High Definition | High definition. |
| HDMI | High-Definition Multimedia Interface | High-Definition Multimedia Interface; used for video and audio transmission. |
| HDOP | Horizontal Dilution of Precision | Horizontal dilution of precision; indicates how satellite geometry affects horizontal positioning accuracy. |
| Heading | — | Heading; the direction in which the front of the Drone is pointing. |
| Heat Sink | — | Heat sink / cooling fin. |
| Horizon Mode | — | Hybrid self-leveling mode; generally self-levels near stick center while allowing flips and rolls with larger stick inputs. |
| Hover | — | Hover; maintaining position and altitude as steadily as possible. |
| HV | High Voltage | High voltage; the specific voltage range depends on the product. |
| Hz | Hertz | Hertz; a unit representing occurrences per second. |
| I²C / I2C | Inter-Integrated Circuit | Inter-Integrated Circuit bus; used to connect sensors and other peripherals. |
| IMU | Inertial Measurement Unit | Inertial measurement unit; typically includes a gyroscope and accelerometer. |
| Interference | — | Interference; such as radio interference, power noise, or electromagnetic interference. |
| IR | Internal Resistance / Infrared | Usually means internal resistance in a battery context, or infrared in an imaging context. |
| Jello | — | Jello effect; wave-like image distortion caused by vibration or similar factors. |
| Joystick | — | Joystick / navigation control stick. |
| kHz | Kilohertz | Kilohertz; commonly used for control frequencies and sampling frequencies. |
| KV / Kᵥ | Motor velocity constant | Motor velocity constant, commonly expressed in rpm/V; it does not mean kilovolts or motor power. |
| Latency | — | Latency; for example, the delay from camera capture to display in the goggles. |
| LC | Inductance–Capacitance | Inductance-capacitance; LC filters are commonly used to suppress power supply noise. |
| LED | Light-Emitting Diode | Light-emitting diode; used for status indication or LED strips. |
| Lens | — | Lens. |
| LHCP | Left-Hand Circular Polarization | Left-hand circular polarization. |
| LiHV | High-Voltage Lithium Polymer Battery | High-voltage lithium polymer battery; requires compatible charging settings. |
| Li-ion | Lithium-ion | Lithium-ion; in FPV, commonly refers to cylindrical-cell battery packs used for longer flight time. |
| Link | — | Link / connection; a LINK button on a device is commonly used for Binding. |
| LiPo | Lithium Polymer | Lithium polymer battery; a common soft-pouch power battery used in FPV. |
| LOS | Line of Sight | Line of sight; may refer to visual flying or an unobstructed wireless link. |
| LPF | Low-Pass Filter | Low-pass filter; attenuates high-frequency noise. |
| LQ | Link Quality | Link quality; in ELRS, it mainly reflects the reception of valid data packets. |
| LR | Long Range | Long range; commonly used to describe long-range Drones and radio links. |
| LVC | Low-Voltage Cutoff | Low-voltage cutoff; limits or cuts output when voltage drops below a threshold. |
| MAG | Magnetometer | Magnetometer / electronic compass sensor. |
| mAh | Milliampere-hour | Milliampere-hour; a unit of battery charge capacity. |
| MAVLink | Micro Air Vehicle Link | Drone communication protocol used for data exchange between flight controllers, ground stations, and peripherals. |
| Mbps | Megabits per second | Megabits per second; commonly used for video transmission bitrate and is different from MB/s. |
| MCU | Microcontroller Unit | Microcontroller unit; the main control chip in devices such as flight controllers and ESCs. |
| MHz | Megahertz | Megahertz; a unit of frequency. |
| Mixer | — | Mixer / mixing configuration; distributes control commands to different motors or servos. |
| MOSFET | Metal-Oxide-Semiconductor Field-Effect Transistor | Metal-oxide-semiconductor field-effect transistor; an important power component in ESCs. |
| Motor | — | Motor. |
| Mount | — | Mount / bracket; may also be used as a verb meaning to install. |
| ms | Millisecond | Millisecond; commonly used for latency and response time. |
| MSP | MultiWii Serial Protocol | MultiWii Serial Protocol; used for flight controller configuration, status data, and some OSD communication. |
| mW | Milliwatt | Milliwatt; a unit of power. |
| ND | Neutral Density | Neutral density; an ND filter reduces the amount of incoming light. |
| Noise | — | Noise; may refer to electrical noise, sensor noise, or image noise. |
| Notch Filter | — | Notch filter; attenuates a specific frequency range. |
| NTSC | National Television System Committee | One of the common analog video standards. |
| OSD | On-Screen Display | On-screen display; overlays information such as voltage, timers, and link status on the screen. |
| OTA | Over-the-Air | Wireless method; OTA update refers to updating firmware over a wireless connection. |
| Packet | — | Data packet. |
| Packet Rate | — | Packet rate / data packet transmission frequency. |
| Pad | — | Solder pad; depending on context, it may also mean a cushioning or anti-slip pad. |
| PAL | Phase Alternating Line | Phase Alternating Line; one of the common analog video standards. |
| Payload | — | Payload; additional equipment carried by a Drone, such as a camera or other device. |
| PCB | Printed Circuit Board | Printed circuit board. |
| PDB | Power Distribution Board | Power distribution board; distributes power to different components. |
| PID | Proportional–Integral–Derivative | Proportional-integral-derivative control. |
| Pin | — | Pin / electrical contact pin. |
| Pit Mode | — | Very low transmit-power mode used to reduce interference with others during ground preparation. Exact behavior depends on the device. |
| Pitch | — | Pitch; in propeller specifications, it can also refer to propeller pitch. |
| Polarization | — | Polarization; such as linear polarization, LHCP, or RHCP. |
| Power | — | Power or power supply; the exact meaning depends on context. |
| PPM | Pulse-Position Modulation | Pulse-position modulation; an older form of multi-channel radio control signal. |
| Prop / Propeller | Propeller | Propeller; Prop is a common abbreviation. |
| Prop Guard | Propeller Guard | Propeller guard / prop guard. |
| Prop Wash | — | Prop wash; disturbed airflow that may cause the Drone to oscillate or shake. |
| Protocol | — | Protocol; defines how data is communicated between devices. |
| PWM | Pulse-Width Modulation | Pulse-width modulation; used for servos, some ESCs, and other control signals. |
| Quad / Quadcopter | Quadcopter | Four-rotor Drone; Quad is a common abbreviation. |
| Racing | — | Racing; focuses on speed, flight lines, and race results. |
| Range | — | Range / effective distance, such as radio control range or video transmission range. |
| Rates | — | Control rate settings; determine the relationship between stick input and target angular velocity. |
| RC | Radio Control | Radio control. |
| Receiver | — | Receiver / Receiver unit. |
| Resolution | — | Resolution, such as 1920 × 1080. |
| RF | Radio Frequency | Radio frequency. |
| RHCP | Right-Hand Circular Polarization | Right-hand circular polarization. |
| Roll | — | Roll; rotation around the Drone's longitudinal axis. |
| RPM | Revolutions Per Minute | Revolutions per minute; a unit of motor speed. |
| RP-SMA | Reverse-Polarity SMA | Reverse-polarity SMA RF connector; its center-contact configuration differs from standard SMA. |
| RSSI | Received Signal Strength Indicator | Received signal strength indicator. |
| RTF | Ready to Fly | Ready-to-fly package; typically includes the main supporting equipment, although necessary setup may still be required. |
| RTH | Return to Home | Return to home / return to the takeoff point; exact behavior depends on the system. |
| RTL | Return to Launch | Return to launch / takeoff point; commonly used in navigation-capable flight controllers. |
| RX | Receiver / Receive | Receiver or receive; a UART RX pin is the data receive pin. |
| S | Series | Series connection; for example, 4S and 6S indicate four or six battery cells connected in series. |
| SBUS / S.BUS | Serial Bus | Serial bus; in FPV, commonly refers to a radio control channel transmission protocol. |
| SD | Secure Digital | Secure Digital storage card standard; FPV devices commonly use microSD cards. |
| Sensor | — | Sensor. |
| Servo | — | Servo; commonly used for fixed-wing control surfaces and gimbals. |
| SMA | SubMiniature version A | Small RF connector commonly used for antenna connections. |
| SNR | Signal-to-Noise Ratio | Signal-to-noise ratio; indicates signal strength relative to noise. |
| Solder / Soldering | — | Solder / soldering; used to connect wires and electronic components. |
| SPI | Serial Peripheral Interface | Serial Peripheral Interface; used for communication between flight controllers and devices such as gyroscopes. |
| Stack | — | Stacked component assembly; in FPV, commonly refers to vertically stacked components such as a flight controller and ESC. |
| Standoff | — | Standoff / spacer; used to secure frames or circuit boards. |
| SWD | Serial Wire Debug | Serial Wire Debug interface; used for chip debugging and firmware programming. |
| Telemetry | — | Telemetry; data sent back by a device, such as voltage, RPM, and link status. |
| Throttle | — | Throttle; controls propulsion power output. |
| Thrust | — | Thrust. |
| Tiny Whoop | — | A class of micro quadcopter with propeller guards. |
| TLM | Telemetry | Common abbreviation for telemetry. |
| TOF / ToF | Time of Flight | Time of flight; in distance measurement, calculates distance using signal travel time. |
| TPU | Thermoplastic Polyurethane | Thermoplastic polyurethane; commonly used for flexible 3D-printed mounts and protective parts. |
| Transmitter | — | Transmitter / transmitting unit. |
| Trim | — | Trim; commonly used for fine adjustment of radio control channels. |
| Tuning | — | Tuning; optimizing control response, filters, or other device parameters. |
| Turtle Mode | — | Turtle Mode / flip-over recovery mode; used to attempt to flip an overturned Drone upright. |
| TVL | Television Lines | Television lines; a common measure of horizontal resolution capability for analog cameras. |
| TX | Transmitter / Transmit | Transmitter or transmit; a UART TX pin is the data transmit pin. |
| UART | Universal Asynchronous Receiver/Transmitter | Universal asynchronous receiver/transmitter; a common serial interface for receivers, GPS modules, air units, and other peripherals. |
| UAV | Unmanned Aerial Vehicle | Unmanned aerial vehicle. |
| U.FL | — | A family of miniature RF connectors commonly used between antennas and modules. |
| UHF | Ultra High Frequency | Ultra high frequency; some radio control links operate within this frequency range. |
| Uplink | — | Uplink; usually refers to data transmission from the ground side to the airborne side. |
| USB | Universal Serial Bus | Universal Serial Bus; used for data transfer, computer connections, or power. |
| UVC | USB Video Class | USB Video Class; supports video transmission over USB. |
| V | Volt | Volt; a unit of voltage. |
| VBAT | Battery Voltage | Battery voltage; also commonly labels battery power or voltage-sensing points and generally refers to total pack voltage. |
| VCC | Circuit Power Supply Label | Indicates a circuit power rail; the actual voltage must be checked in the wiring diagram and should not automatically be assumed to be 5 V. |
| VFR | Valid Frame Rate | Valid frame rate; used by some radio systems to indicate the proportion of valid received frames. |
| Vibration | — | Vibration; may affect gyroscope data and video quality. |
| VIN | Voltage Input | Voltage input / power input. |
| Voltage | — | Voltage. |
| Voltage Sag | — | Voltage sag / voltage drop; a reduction in battery voltage under load. |
| VOUT | Voltage Output | Voltage output / power output. |
| VRX | Video Receiver | Video receiver / video Receiver unit. |
| VTX | Video Transmitter | Video transmitter / video transmitting unit. |
| W | Watt | Watt; a unit of power. |
| WDR | Wide Dynamic Range | Wide dynamic range; improves image performance in scenes with large differences between bright and dark areas. |
| Wh | Watt-hour | Watt-hour; a unit of battery energy. |
| White Balance | — | White balance; adjusts image colors for different light sources. |
| XT30 / XT60 | — | Common power connector models; no expanded English name is required. |
| Yaw | — | Yaw; rotation around the yaw axis of the Drone. |
| Z-axis | — | Z-axis; one of the three-dimensional coordinate axes. Its positive direction depends on the coordinate system being used. |
![]()
| No. | Component Name | Function |
|---|---|---|
| 1 | Camera | Captures the FPV image during flight. |
| 2 | Lens | Focuses incoming light onto the camera image sensor. |
| 3 | Camera Coaxial Cable | Connects the camera to the air unit and transmits the image signal. |
| 4 | Air Unit | Processes the camera image and wirelessly transmits it to a compatible receiver unit. |
| 5 | Cooling Assembly | Helps dissipate heat generated by the air unit during operation. |
| 6 | VTX Antennas ×2 | Used for wireless signal transmission and reception by the air unit. |
| 7 | MMCX Antenna Connector | Connects the VTX antenna to the air unit. |
| 8 | USB-C Port | Used to connect compatible devices via USB cable. |
| 9 | Power Cable Port | Connects the power cable to supply power to the air unit. |
![]()
| No. | Component Name | English Name | Function |
|---|---|---|---|
| 1 | Bind Button | Bind Button | Starts Binding so the air unit can establish a connection with a compatible receiver unit. |
| 2 | SD Card Slot | SD Card Slot | Used to insert a microSD card for storing videos recorded by the air unit. |
| 3 | Status LED | Status LED | Indicates the operating and connection status of the air unit through LED colors and flashing patterns. |
![]()
| No. | Component Name | Function |
|---|---|---|
| 1 | Camera | Captures the FPV image during flight. |
| 2 | Lens | Focuses incoming light onto the camera image sensor. |
| 3 | Camera Coaxial Cable | Connects the camera to the air unit and transmits the image signal. |
| 4 | Air Unit | Processes the camera image and wirelessly transmits it to a compatible receiver unit. |
| 5 | Air Unit Housing | Protects the internal components of the air unit. |
| 6 | VTX Antennas ×2 | Used for wireless signal transmission and reception by the air unit. |
| 7 | IPEX-1 Antenna Connector | Connects the VTX antenna to the air unit. |
| 8 | Power and Signal Pads | Used for soldering power wires and signal wires connected to the flight controller. |
| 9 | Mounting Holes | Used to secure the air unit to the frame or mounting bracket. |
![]()
![]()
![]()
![]()
| No. | Component | Function |
|---|---|---|
| 1 | Eyepiece | Used to view the image displayed inside the goggles. |
| 2 | Face Pad | Fits against the face to provide wearing support and reduce light leakage. |
| 3 | Infrared Proximity Sensor | Detects whether the goggles are being worn and automatically controls the screen on/off state. |
| 4 | Head Strap Buckle | Used to connect and secure the goggles head strap. |
| 5 | Power Port | Connects an external power source to power the goggles. |
| 6 | VTX Antennas ×4 | Used to establish a wireless video link with compatible video transmission devices. |
| 7 | Cooling Vent | Allows airflow to help dissipate heat from the device. |
| 8 | Front Cover | Covers the front of the goggles and can be removed and replaced. |
| 9 | LED Light Strip | Illuminated component located on the front cover. |
| 10 | Bind Button | Used to start Binding between the goggles and the air unit. |
| 11 | Record Button | Used to start or stop recording. |
| 12 | Back Button | Used to return to the previous menu or exit the current mode. |
| 13 | Five-Way Button | Move it to select menu items and press it to confirm. |
| 14 | AV Input Port | Used to input compatible analog video signals, output PPM head tracking signals, and update head tracking firmware. |
| 15 | HDMI Input Port | Used to receive HDMI video from external devices. |
| 16 | SD Card Slot | Used to insert a microSD card for storing recordings and other files. |
| 17 | HDMI Output Port | Used to output video to an external display device. |
| 18 | IPD / Diopter Adjustment Knob | Used to adjust the distance between the eyepieces and the diopter so the image is suitable for both eyes. |
![]()
![]()
| No. | Component Name | Function |
|---|---|---|
| 1 | Five-Way Button | Move it to navigate menu items and press it to confirm. |
| 2 | Back Button | Returns to the previous menu or exits the current mode. |
| 3 | Record Button | Starts or stops recording. |
| 4 | Bind Button | Starts Binding between the goggles and a compatible air unit. |
| 5 | Cooling Vent | Allows airflow to help dissipate heat from the device. |
| 6 | LED Light Strip | Illuminated component located on the front of the goggles. |
| 7 | Top Cover | Covers and protects the internal components in the upper section of the goggles. |
| 8 | Face Pad | Fits against the face to provide support and reduce light leakage. |
| 9 | Head Strap Buckle | Used to attach and secure the goggles head strap. |
| 10 | Eyepiece | Used to view the FPV image displayed inside the goggles. |
| 11 | Lens Mounting Hole | Used to install and secure the bracket for additional lenses. |
![]()
![]()
![]()
| No. | Chinese Name | English Name | Function |
|---|---|---|---|
| 1 | Red Bird Omnidirectional Antennas ×2 | Red Bird Omnidirectional Antennas ×2 | Receives video transmission signals using left-hand circular polarization (LHCP). |
| 2 | RP-SMA Antenna Connector | RP-SMA Antenna Connector | Connects removable external antennas. |
| 3 | 5-Way Navigation Button | 5-Way Navigation Button | Moves through menu options; press the center button to confirm. |
| 4 | Bind Button | Bind Button | Starts Binding between the receiver unit and a compatible air unit. |
| 5 | Two-Prong Mount | Two-Prong Mount | Connects to a compatible mount to secure the receiver unit. |
| 6 | Record Button | Record Button | Starts or stops recording. |
| 7 | Back Button | Back Button | Returns to the previous menu or exits the current mode. |
| 8 | microSD Card Slot | microSD Card Slot | Accepts a microSD card for saving recordings or loading firmware update files. |
| 9 | DC Power Input | DC Power Input | Connects an external DC power source. |
| 10 | Directional Patch Antennas ×2 | Directional Patch Antennas ×2 | Improves video signal reception in the direction the antennas are facing. |
| 11 | Cooling Fan | Cooling Fan | Located behind the front grille to help dissipate heat from the device. |
| 12 | Cooling Vents | Cooling Vents | Provide airflow paths for cooling. |
| 13 | Mini HDMI Output | Mini HDMI Output | Outputs video to compatible goggles or displays. |
| 14 | Avatar VRX Receiver | Avatar VRX Receiver | Receives and decodes compatible Avatar video transmission signals. |
| 15 | Product Box | Product Box | Used for product packaging and protection during transportation. |
| 16 | HDMI Cable | HDMI Cable | Connects the receiver unit to a compatible display device. |
| 17 | 1-to-2 DC Power Splitter Cable | 1-to-2 DC Power Splitter Cable | Splits one DC power source to supply two compatible devices. |
| 18 | Double-Sided Adhesive Pads | Double-Sided Adhesive Pads | Used to attach and secure the device. |
| 19 | Hex Keys | Hex Keys | Used to install or remove compatible hex screws. |
| 20 | Mounting Screw and Nut | Mounting Screw and Nut | Used to secure mounting connections. |


| No. | Component Name | English Name | Function |
|---|---|---|---|
| 1 | Camera Mount | Camera Mount | Secures the camera. No camera is installed in the image. |
| 2 | Pitch Motor | Pitch Motor | Drives the camera up and down along the pitch axis. |
| 3 | Roll Motor | Roll Motor | Compensates for left and right camera tilt. |
| 4 | Yaw Motor | Yaw Motor | Rotates the gimbal left and right along the yaw axis. |
| 5 | Gimbal Arm | Gimbal Arm | Connects and supports the components of each gimbal axis. |
| 6 | Gimbal Base | Gimbal Base | Supports the gimbal and houses the connection interfaces. |
| 7 | Vibration Damping Ball | Vibration Damping Ball | Reduces vibration transmitted from the vehicle to the gimbal. |
| 8 | Mounting Bracket | Mounting Bracket | Secures the gimbal to the vehicle. |
| 9 | Power and Control Port | Power and Control Port | Supplies power to the gimbal and receives control signals. |
| 10 | Receiver Power Output | Receiver Power Output | Supplies power to the receiver, with a 7 V output and a maximum current of 0.3 A. |
| 11 | Coaxial Cable | Coaxial Cable | Connects the gimbal to a compatible air unit and transmits the camera signal. |
| 12 | Coaxial Cable Connector | Coaxial Cable Connector | Connects to the camera port on a compatible air unit. |
| 13 | Firmware Upgrade Port | Firmware Upgrade Port | Used for firmware updates and control configuration. Pins are TX, RX, and GND. |



| No. | Component | Function |
|---|---|---|
| 1 | Canopy | Protects the camera and internal components of the Drone. |
| 2 | Camera Mount | Used to install and secure the camera. |
| 3 | Ascent Lite+ Air Unit Kit | Includes the camera, air unit, and antenna for capturing and wirelessly transmitting video. |
| 4 | Air Unit Mount | Used to install and secure the air unit. |
| 5 | AXON 1S AIO V2.0 Flight Controller | Integrates flight control, ESC, and receiver functions. |
| 6 | Frame | Supports and connects the components of the Drone. |
| 7 | 1102 Brushless Motor | Drives the propeller to rotate. |
| 8 | Propeller Guard | Surrounds the propeller to provide impact protection. |
| 9 | Propeller | Rotated by the motor to generate thrust for the Drone. |
| 10 | FPV Camera | Captures the first-person-view video during flight. |
| 11 | VTX Antenna | Used to transmit and receive wireless signals for the air unit. |
| 12 | Curve Micro 16 Drone | Fully assembled Drone. |
| 13 | Carrying Case | Used to store and carry the Drone and accessories. |
| 14 | Wrist Strap | Makes the carrying case easier to carry. |
| 15 | Quick Start Guide | Provides product setup and basic operating instructions. |
| 16 | Six-Channel Charger | Charges compatible 1S high-voltage lithium batteries. |
| 17 | Spare Propellers | Used to replace damaged or worn propellers. |
| 18 | 4-Pin Cable | Used to connect compatible 4-pin ports. |
| 19 | 6-Pin to 4-Pin Cable | Used to connect compatible 6-pin and 4-pin ports. |
| 20 | USB Adapter Board | Used for USB interface adapter connections. |
| 21 | USB Charging Cable | Connects the charger to a USB power source. |
| 22 | Screwdriver | Used to install or remove compatible screws. |
| 23 | Propeller Removal Tool | Helps remove the propeller from the motor shaft. |



| No. | Component | Function |
|---|---|---|
| 1 | Canopy | Protects the camera and internal components of the Drone. |
| 2 | Ascent Lite Air Unit | Captures the flight video and wirelessly transmits it to compatible FPV goggles. |
| 3 | 1102 Brushless Motor | Drives the propeller to rotate. |
| 4 | Tri-Blade Propeller | Rotated by the motor to generate thrust for the Drone. |
| 5 | Injection-Molded Frame | Supports and connects the components of the Drone. |
| 6 | Propeller Guard | Surrounds the propeller to provide impact protection. |
| 7 | 2S Flight Battery | Powers the Drone; three batteries are shown in the kit image. |
| 8 | Status LED | Indicates flight modes and device status through LED color and flashing patterns. |
| 9 | Optical Flow Sensor Module | Detects ground movement below the Drone and works with distance measurement to assist with position holding. |
| 10 | Aluminum Heat Sink | Helps dissipate heat generated by the internal electronic components. |
| 11 | Protos Drone | Fully assembled Drone. |
| 12 | Ascent Goggles | Receives and displays the video transmitted by the Drone. |
| 13 | A-Link Radio Controller | Sends control commands to operate the Drone and switch flight modes. |
| 14 | 2S Charging Hub | Charges compatible flight batteries sequentially and supports storage mode. |
| 15 | Goggles Battery | Powers the goggles through the power cable. |
| 16 | Carrying Case | Used to store and carry the Drone, goggles, radio controller, and accessories. |
| 17 | Spare Canopy | Used to replace a damaged or worn canopy. |
| 18 | USB-C Cable | Connects compatible USB-C devices for charging or data transfer. |
| 19 | XT30 to DC Power Cable | Connects the goggles battery to the goggles power port. |
| 20 | Lens Cleaning Cloth | Used to remove dust and smudges from the lens surface. |
| 21 | Spare Tri-Blade Propellers | Used to replace damaged or worn propellers. |
| 22 | Additional Lens Frame | Used to install compatible lenses and secure them inside the goggles. |
| 23 | Screwdriver | Used to install or remove compatible screws. |
| 24 | Propeller Removal Tool | Helps remove the propeller from the motor shaft. |
| 25 | Hex Wrench | Used to install or remove compatible hex screws. |
| 26 | Button Pin Tool | Used to press small recessed buttons. |
| 27 | Decorative Stickers | Used to decorate the Drone or accessories. |



| No. | Component | Function |
|---|---|---|
| 1 | Moonlight Camera | Captures the flight view and works with the Moonlight system for video transmission and recording. |
| 2 | ND Filter | Reduces the amount of light entering the lens, making it easier to adjust exposure in bright environments. |
| 3 | Camera Protective Cover | Covers and protects the upper part of the camera. |
| 4 | 1303 Brushless Motor | Drives the propeller to rotate. |
| 5 | 2-Inch Tri-Blade Propeller | Generates thrust for the Drone while rotating. |
| 6 | Injection-Molded Frame | Supports and connects the components of the Drone. |
| 7 | Propeller Guard | Surrounds the propeller to provide impact protection. |
| 8 | Battery Anti-Slip Pad | Increases friction between the battery and frame and works with the battery strap to secure the battery. |
| 9 | XT30 Power Connector | Connects the flight battery to power the Drone. |
| 10 | Flight Controller Micro-USB Port | Connects to a computer for flight controller configuration and maintenance. |
| 11 | VTX Antennas ×2 | Used to transmit and receive wireless signals for the Moonlight video transmission system. |
| 12 | ELRS Receiver Antenna | Receives control signals transmitted by a compatible radio controller. |
| 13 | Moonlight Air Unit | Processes and wirelessly transmits the camera video and supports onboard recording. |
| 14 | Battery Strap | Secures the flight battery to the frame. |
| 15 | Gofilm 20 Drone | Fully assembled Drone. |
| 16 | Packaging Box | Used for product packaging and protection during transportation. |
| 17 | Quick Start Guide | Provides product setup and basic operating instructions. |
| 18 | Micro-USB Data Cable | Connects the flight controller to a computer for configuration and data communication. |
| 19 | Spare Tri-Blade Propellers | Used to replace damaged or worn propellers. |
| 20 | Hex Wrench | Used to install or remove compatible hex screws. |
| 21 | Spare Screws | Spare Screws |
| 22 | Moonlight Air Unit Update Cable | Moonlight VTX Upgrade Cable |



Walksnail Ascent FPV VRX Pro — Terminology
| No. | Component Name | Function |
|---|---|---|
| 1 | Red Bird Pro Antennas ×2 | Receive Ascent video transmission signals using LHCP polarization. |
| 2 | RP-SMA Antenna Connector | Connects removable antennas. |
| 3 | LINK Bind Button | Starts Binding between the receiver unit and a compatible air unit. |
| 4 | Cooling Vent | Provides an airflow path for heat dissipation. |
| 5 | Cooling Fan | Actively moves air to help cool the device. |
| 6 | microSD Card Slot | Used to insert a storage card for saving recordings or loading firmware update files. |
| 7 | 6-Pin Serial Passthrough Port | Provides SBUS, 5V, GND, RX, TX, and GND pins. |
| 8 | Five-Way Navigation Button | Move it to navigate menu items and press the center button to confirm. |
| 9 | BACK Button | Returns to the previous menu. |
| 10 | REC Button | Starts or stops recording. |
| 11 | DC Power Input | Connects an external DC power source. |
| 12 | USB-C Port | Used for firmware updates and UVC video output. |
| 13 | HDMI Output Port | Outputs video to compatible goggles or displays. |
| 14 | 1/4-Inch Tripod Thread | Used to mount the device on a tripod or compatible bracket. |